Orion 2000 Manual do Utilizador
Consulte online ou descarregue Manual do Utilizador para Modems Orion 2000. Orion 2000 User's Manual Manual do Utilizador
- Página / 80
- Índice
- MARCADORES
- Orion 2000 1
- Contents 2
- 1. Before You Begin 5
- Supplied 6
- Not Supplied 6
- Installing the Hardware 10
- Uninstalling the USB Driver 27
- 5. Telnet commands 32
- Undebug 34
- Password 36
- User-Level 36
- Interfaces 50
- Web-access 54
- Access-list 54
- PPPoE-Forwarding 55
- Cpe-limit 55
- 6. Mode of Operation 57
- Routing mode 58
- NAT/Routing mode 59
- CM>ip natroute enable 60
- CM>reset 60
- 7. Web User Interface 61
- Cable Modem Status 62
- Downstream 63
- Upstream 64
- Upstream Burst 65
- Operation Parameters 66
- Event Log 67
- NAT/Router configuration 68
- Router Mode 70
Resumo do Conteúdo
Orion 2000 Cable Router User’s Guide Rev. 1.2a Firmware 2.59.2004 April 14th, 2003
User’ Guide 10 6. Click “Finish”. You will see below screen, and then select ‘Yes.’ Now you can connect the USB cabl
User’ Guide 11 or surge protector. 5. You are now ready to install the software drivers. Installing the Software
User’ Guide 12 2. Insert the CD into the PC’s CD-ROM and click Next. You will see the following screen. 3. Sele
User’ Guide 13 4. Check the CD-ROM drive check box and verify that the CD is in the CD-ROM drive. Click Next to hav
User’ Guide 14 6. Click Next. The computer automatically installs the necessary driver files. You may see the fol
User’ Guide 15 8. After files copying is done, you will see the following screen: 9. Click Finish to complete
User’ Guide 16 10. Choose Yes to restart your computer. 11. After the computer is rebooted, verify that the USB
User’ Guide 17 3. Select Automatic search for a better driver (Recommended) and click (Next). The computer autom
User’ Guide 18 4. Click Next. The computer automatically installs the necessary driver files. 5. Click Finish a
User’ Guide 19 Installing the Software Drivers in Windows 2000 Operating System To install the cable modem softwar
User’ Guide 2 Contents 1. BEFORE YOU BEGIN ...
User’ Guide 20 3. Select Search for a suitable driver for my device (recommended. Then select Next. You will see
User’ Guide 21 4. Check the CD-ROM drive check box and verify that the CD is in the CD-ROM drive. Click Next to h
User’ Guide 22 5. Click Next to install the driver files for the cable modem. You will see the following screen.
User’ Guide 23 2. Choose the software automatically (Recommended). Click Next to continue. You will see the foll
User’ Guide 24
User’ Guide 25 3. Click Finish to complete the installation. Troubleshooting the USB Installation None of the LED
User’ Guide 26 device drivers 4. Select USB Composite Device and click Remove 5. Click Refresh The Add New Hardwa
User’ Guide 27 • Try restarting the computer so that it could re-establish a connection with the cable modem. • Pow
User’ Guide 28 for use with your cable modem. The cable modem requires TCP/IP to be installed. Contact your cable s
User’ Guide 29 2) Click the Device Manager tab and look for a yellow exclamation point or red X over the NIC in the
User’ Guide 3 Debug...
User’ Guide 30 LEDs on the Front of the Modem • power: Indicates that the cable modem has successfully completed
User’ Guide 31 1. power: This is where you plug the include power adapter. Remember to use only the power adapter
User’ Guide 32 5. Telnet commands The Cable Router telnet Login and Password: Login: Password: ** Note: C
User’ Guide 33 To list keywords or arguments, enter a question mark (?) in place of a keyword or argument. Include a
User’ Guide 34 Debug ¾ debug Display corresponding message, the protocol debug just show packet information send to
User’ Guide 35 all Disable all debugging functions Image ¾ image upgrade {1|2} Download the spe
User’ Guide 36 Ping statistics: Packets sent: 6; received: 6; Lost: 0 (0% loss) Round trip time in milli-seconds
User’ Guide 37 ¾ show dhcp Display all options provided in DHCP response. Example: CM>show dhcp TFTP Server IP a
User’ Guide 38 ¾ show interface Display interface information Example: CM>show interface ? ethernet Disp
User’ Guide 39 Upstream Symbol Rate : 2560 ksym/sec Upstream Frequency : 28688000 Hz Upstream
User’ Guide 4 NAT mode...
User’ Guide 40 RIP status: Enable RIP send version: 2 Downstream information FEC Lock :
User’ Guide 41 RIP expire time: 180 seconds RIP garbage time: 120 seconds TFTP Server IP address : 2
User’ Guide 42 Example: CM>show downstream FEC Lock : Locked Downstream Frequency : 561000000 Hz Downstream Modul
User’ Guide 43 WAN SETUP : NAT public IP configuration : Automatically NAT public IP address : 68.4.103.29 Subnet
User’ Guide 44 Example: CM>show access-list Access List ID Control Address 41 Permit 00D0
User’ Guide 45 Set TFTP filename to "ram.cpr" ¾ tftp server {Server IP address} Establishes the IP addres
User’ Guide 46 DHCP server enable NAT DHCP Server Pool Table : NAT DHCP server support 20 IP pools NAT DHCP serve
User’ Guide 47 Provision assigned DNS 68.4.16.30 Provision assigned DNS 68.6.16.30 DHCP server lease time : 1800 Pr
User’ Guide 48 LAN SETUP : Ethernet interface IP address 192.168.100.1 subnet-mask 255.255.255.224 NAT DHCP Server P
User’ Guide 49 IP Mapping Table: Index Global IP Local IP 1 68.5.203.16 192.168.100.22
User’ Guide 5 1. Before You Begin Your new cable modem provides high-speed access to the Internet by an active Inter
User’ Guide 50 Set NAT public Gateway IP to 68.5.202.1 CM>show nat config NAT : Enable WAN SETUP : NAT public IP
User’ Guide 51 ¾ interface ethernet rip {enable|disable} Enable/disable RIP on ethernet interface ¾ interface ethe
User’ Guide 52 IP ¾ ip route {enable/disable} Enable/disable routing with RIP. Default routing mode is RIPv2.
User’ Guide 53 Set garbage collection time ¾ rip silence-mode {enable/disable} -- default value is disable Enable/
User’ Guide 54 Web-access ¾ web-access cpe {enable|disable} Enable|disable the CM web access via CPE interface ¾
User’ Guide 55 ¾ access-list delete {list ID|all} Delete a specific access-list or delete all access-list PPPoE-Fo
User’ Guide 56 Reboot cable modem Quit ¾ quit Disconnect telnet.
User’ Guide 57 6. Mode of Operation Bridge mode Bridge mode is the factory default setting. NAT mode ¾ ip nat enab
User’ Guide 58 Routing mode ¾ ip route enable Default setting for routing mode is RIPv2 with DHCP disabled automati
User’ Guide 59 NAT/Routing mode ¾ ip natroute enable Enable NAT and Routing simultaneously. Enable natroute will al
User’ Guide 6 Prepare Your Area for Cable Modem Installation Before installing your cable modem, you should first pr
User’ Guide 60 CM>interface cable rip auth-mode md5 CM>rip key-chain 1 1 key-string abcdefg CM>ip natroute e
User’ Guide 61 7. Web User Interface Accessing the Web User Interface 1. The PC connected to the cable modem must
User’ Guide 62 Cable Modem Status
User’ Guide 63 Downstream
User’ Guide 64 Upstream
User’ Guide 65 Upstream Burst
User’ Guide 66 Operation Parameters
User’ Guide 67 Event Log
User’ Guide 68 NAT/Router configuration Bridge Mode In Bridge mode, no configuration is required. The Orion 2000 Ca
User’ Guide 69 NAT Mode Gateway LAN Interface • IP Address Gateway private NAT IP address • Subnet Gatew
User’ Guide 7 o An active Ethernet port on your PC or Macintosh Be sure to follow the instructions provided for the
User’ Guide 70 Router Mode
User’ Guide 71 Routing Protocol LAN Interface • Public IP Address Gateway(same as the Cable Modem’s ethernet interf
User’ Guide 72 • Authentication Key Chain Key Chain 1 • Listing of key • Input key Index ID, Key String, Start
User’ Guide 73 Submit • Click “Submit” to change displayed parameters Reset • Click “Reset” to use displayed param
User’ Guide 74 NAT Router Mode Routing Protocol
User’ Guide 75 Gateway LAN Interface • Gateway Public IP Address for LAN Interface subnet and NAT-private subnet
User’ Guide 76 • Authentication mode • Authentication Key Chain Key Chain 1 • Listing of key • Input key Ind
User’ Guide 77 • Listing of key Chain 2 • Input key Index ID, Key String, Start time, and End time Submit • Clic
User’ Guide 78 DHCP Gateway LAN Setup • IP Address (Gateway for private IP subnet in NAT mode) (Gateway for Publi
User’ Guide 79 • Domain Name Service Supports up to four DNSs by clicking “Add” or “Delete” to insert or remove DNS
User’ Guide 8 To install the cable modem software drivers using the Windows operating system: 1. Double click the “Se
User’ Guide 80 9. DOCSIS configuration file VSIF tag support This feature allows downloading Cable Router configura
User’ Guide 9 5. Click “Next>”. You will see the following ‘Complete’ screen.
© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.092 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais